How to plan a golf simulator room in five steps
A five-step planning checklist for a golf simulator room: space, power and data, hardware, software and computer, then install. What to decide and measure at each step.
- Topic
- How To
- Published
- Read
- 8 min
- Carry
- 1,748 words

In this guide 8 sections
- The five steps on one page
- Step 1: Which room, and what is it for?
- Step 2: How do you plan power and data for a simulator?
- Step 3: In what order should you choose the hardware?
- Step 4: How do you choose the software and computer?
- Step 5: How do you install and calibrate it?
- Which planning decisions are hardest to change later?
- Questions people ask
Plan a golf simulator room in five steps, in this order: the space, the power and data, the hardware, the software and computer, and finally the install and calibration. Each step limits the next one. The room decides which launch monitor fits, the launch monitor decides which software you can run, and the software decides what computer you need. Skip ahead and you end up returning parts.
Prices checked November 2026.
The five steps on one page
| Step | What you decide | What you measure or check | What forces a redo |
|---|---|---|---|
| 1. Space | Which room, and what it's for | Ceiling, width, depth, obstructions, ceiling material, windows | Switching rooms after design work starts |
| 2. Power and data | Circuits, outlet locations, network and video runs | Panel capacity, distance from PC to projector and launch monitor | Discovering you need ceiling power after the enclosure is up |
| 3. Hardware | Enclosure type, launch monitor, screen, projector, mat | Mounting ranges, throw distance, screen size against room width | A launch monitor or projector that doesn't fit the room |
| 4. Software and computer | Simulation software, then the PC | Launch monitor compatibility, PC requirements | A PC that the software won't run on |
| 5. Install and calibrate | DIY or hired, and the calibration plan | Projector alignment, launch monitor level and angles, test shots | Weeks of practice on bad numbers |
Step 1: Which room, and what is it for?
Pick one room. Not a shortlist. Room dimensions drive the enclosure, the screen size, the projector position, the turf footprint and where the computer lives, so changing rooms later means starting most of the plan over.
Then decide what the room is for, because it changes the layout:
- Practice room. A clean hitting lane, a launch monitor that reads club data, a bright and accurate image, and a spot for a second display showing numbers.
- Entertainment room. Seating behind the golfer, lighting you can dim, audio, maybe a TV for watching golf. That takes depth and electrical planning.
- Both. Fine, but it has to be planned that way from the start. Seating needs depth behind the swing, and a room that also shows movies competes with golf for screen and projector choices.
Step 1 checklist
- Ceiling height from the finished floor to the lowest obstruction in the hitting area (beam, duct, light, sprinkler head, garage door hardware), minus about 1 to 1.5 inches for turf and mat.
- Width wall to wall, and the location of any posts or soffits.
- Depth from the wall the screen will hang on to the opposite wall.
- Ceiling material: drywall over joists, plywood or exposed framing can take a mount; a drop ceiling has to come out; concrete needs blocking.
- Windows, skylights and doors that could put light on the screen or open into the swing.
- Photos of all four walls and the ceiling. Measure twice: a 2-inch error decides whether some overhead units fit.
- Everyone who has to sign off on the room has seen this list.
As a rough guide, you want at least 9 feet of ceiling, 12 feet of width and about 17 feet of depth, with 10, 15 to 16 and 19 to 20 feet being comfortable. The room dimensions reference has the thresholds and two worked examples.
Check your own room: the golf simulator room size calculator applies these numbers to your ceiling, width and depth and lists the launch monitors that fit.
Step 2: How do you plan power and data for a simulator?
Do this before you pick hardware, because it decides where hardware can go. Electrical and network runs are cheap while the walls are open and the enclosure isn't built, and awkward after.
Power
- Two to three dedicated circuits. A gaming PC can pull 8 to 12 amps under load. A bright laser projector draws 3 to 5 amps. Neither should share a circuit with a space heater or a garage freezer.
- Ceiling outlets. A ceiling-mounted projector needs power at the mount, and so does an overhead launch monitor. Put a box at each likely position.
- Surge protection. Run the launch monitor, PC and projector through a good surge protector or a UPS.
- Permits. New circuits may need one where you live. Find your electrician now so scheduling doesn't hold up the install.
Data and video
- Ethernet. Hardwire the PC and, where the unit supports it, the launch monitor. If the room is being framed or renovated, pull Cat6 now.
- HDMI. Measure the real path from the PC to the projector, up the wall and across the ceiling. Long runs are where a fiber HDMI cable earns its price.
- Extras. If you want speakers, a second display or dimmable lighting, plan their wiring now even if you buy the gear later.
Light belongs in this step too. Any light that lands on the screen washes out the image. Block windows that face the screen and keep fixtures over or behind the golfer rather than between the golfer and the screen.
Step 3: In what order should you choose the hardware?
Pick the hardware as a system, in this order. Each item gets sized to the ones before it.
- Enclosure type. A permanent frame suits a dedicated room. A retractable screen suits a garage that still parks a car. A folding or wall-mounted unit suits a room that has another job. The type sets where the screen hangs and where things can mount. The enclosure comparison covers each type.
- Launch monitor. Check its mounting range against your ceiling number from step 1. ProTee lists 9 to 10 feet for the VX, Uneekor lists 9 to 10 feet for its overhead units, and Foresight lists 9.5 to 10.5 feet for the Falcon. Floor radar needs extra depth behind the ball. The launch monitor picks are sorted by room type.
- Screen size. As wide as the room allows after side panels and padding, at the right aspect ratio for your projector.
- Projector. Throw distance = throw ratio x image width. A BenQ TK710STi (about $2,000 to $2,200) has a 0.69 to 0.83 throw ratio, so a 10-foot-wide image needs the lens 6.9 to 8.3 feet from the screen. Check that spot is on the ceiling where you planned an outlet, out of the swing, and in front of the golfer's head so it doesn't cast a shadow. More in the projector guide.
- Hitting mat and turf. Sized to the hitting area, with turf running to the enclosure walls.
Order nothing until all five fit on paper. A projector that's right for one screen size can be wrong for the next, and a launch monitor that's perfect for one room can need a drop mount in another.
Step 4: How do you choose the software and computer?
Software comes after the launch monitor because the launch monitor limits it. The computer comes last because the software sets its spec.
- Check compatibility first. GSPro is $250 a year and connects to a long list of launch monitors, but some brands require their own paid software tier before they'll talk to it. Trackman units run Trackman's own software rather than GSPro.
- Match the use. Course play, practice with club data, online events and multiplayer games are different priorities, and programs lean different ways. The software comparison covers the main options.
- Then spec the PC. Trackman's software requires an Intel processor and does not support AMD processors or graphics; its current support pages list an RTX 4070 Ti or 5070 Ti as the minimum GPU and 32 GB of RAM. GSPro and most other programs run fine on AMD. The computer guide lists the requirements per program.
- Budget the subscription. Many programs and launch monitors renew yearly. Put that number on the plan next to the hardware.
Decide where the PC sits, too: behind the golfer or in a cabinet, with a wireless keyboard and mouse, never where a ball can reach it.
Step 5: How do you install and calibrate it?
Installing is the easy part. Calibration is where builds quietly go wrong. A slightly mis-aimed launch monitor or a skewed projector doesn't announce itself. You just practice for months with numbers that don't match the course.
Install order
- Electrical and network rough-in, then any wall or ceiling finishing.
- Enclosure frame, screen and side panels, then ceiling and wall padding.
- Turf and mat.
- Projector and launch monitor mounts, anchored into joists or solid blocking.
- PC, cables and software.
Calibration checklist
- Projector. Fill the screen edge to edge without spill, using lens shift or corner adjustment. Allow 30 to 60 minutes to do it properly.
- Launch monitor. Follow the manufacturer's leveling and alignment steps for its height and angle, then run the software's calibration.
- Test shots. Hit clubs you know the outdoor numbers for. If a 7-iron that carries 160 outside shows 175, stop and recheck before you trust anything.
- Safety. Screen tension, frame joints, padding on every hard surface a shank can reach, and a clear 8-foot swing circle.
DIY or hired?
A pipe-frame enclosure, a floor launch monitor and a projector are a reasonable DIY job; plan a full weekend for a retractable or framed enclosure and longer for a first build. Hiring it out commonly adds about $2,000 to $8,000 depending on the scope. Platform systems like Golfzon's are installed by Golfzon's own engineers, with your contractor building the platform and booth to Golfzon's plans. If you're doing it yourself, the DIY build guide walks through each part.
Which planning decisions are hardest to change later?
The earlier a decision sits in the order, the more depends on it, and the more it costs to change.
| Decision | Step | Cost to change after install |
|---|---|---|
| Which room | 1 | Start over |
| Practice vs entertainment layout | 1 | High: seating, lighting and audio rework |
| Circuits, ceiling outlets, network runs | 2 | High once walls and enclosure are finished |
| Enclosure type | 3 | High: new frame, new mounting positions |
| Launch monitor type | 3 | Medium to high: may change mounts, software and PC |
| Projector model | 3 | Medium: new mount position if the throw ratio differs |
| Software subscription | 4 | Low, if the launch monitor supports the alternative |
| Mat, pad color, side display | 3 to 5 | Low: swap it |
Get the top half of that table settled and written down before you spend money, and you keep the freedom to change the bottom half whenever you like. Launch House has a longer write-up of its design process if you want another view of the same sequence. When the plan is done, the cost breakdown will help you price it.


